BLACK SQUARE A36TC | 1000 HP EXPERIMENTAL RACE CONCEPT | MSFS 2020 INSTALL 1. Exit MSFS. Back up your full aircraft package, especially any layout.json. 2. Find the specific Black Square A36TC SimObjects/Airplanes/ folder that currently contains the two original CFG files (use a file content comparison to confirm). 3. Replace ONLY that folder's engines.cfg and flight_model.cfg with the files from modified/. 4. If your install uses a layout.json file, it may require regenerating to register changed file sizes (especially for Community packages); use a trusted MSFS layout generator. 5. Launch and test at a low fuel load in clear weather. Use gradual throttle, full rudder available, and monitor RPM, speed, temperatures and directional control. Restore originals/ to revert. WHAT WAS CHANGED ENGINE: rated engine HP 300 -> 1000, power scalar 0.87 -> 2.90. MSFS's power scalar changes net torque; the rated-HP number itself does NOT guarantee true output. 3 -> 4 prop blades, power absorption coefficient 1.30 -> 1.55, prop inertia 1.6 -> 2.4, a modest prop lift tweak. HANDLING: rudder area 14.5 -> 16.2 sq ft, effectiveness 0.85 -> 1.03, rudder deflection scalar 0.60 -> 0.72, rudder lift 1.30 -> 1.38, yaw stability 1.0 -> 1.1 and roll stability 0.8 -> 0.9. P-factor, prop torque and gyro effects all remain 1.0 rather than being artificially removed. AERO: drag_coef_zero_lift 0.0300 -> 0.0280; parasite_drag_scalar 0.920 -> 0.865; Oswald efficiency 0.65 -> 0.72; induced_drag_scalar 1.15 -> 1.10. UNCHANGED: Vne/max indicated speed, maximum gross weight, G limits, wing area, stall tables, fuel capacity and other safety-related values. REALISM AND LIMITATIONS This is a fictional, extreme experimental race build, NOT an actual approved STC, physically validated Bonanza performance model, or an airworthy design. A 1000-HP Bonanza would require major structural, cooling, fuel-system, drivetrain, propeller and flutter work. The 4-blade prop and enlarged rudder are approximations in the flight model; no 3D geometry or artwork is changed. Drag changes represent conceptual fairings, sealing, surface finishing and cleanup, not certified measured reductions. The extra engine power may be overridden by Black Square's custom engine code, which is not included in the supplied files. 1000 HP and climb rate cannot be guaranteed without in-sim tests. Existing 205 KIAS limit remains; overspeed is still possible and must be avoided. TUNING AFTER TEST FLIGHT If RPM bogs badly at wide-open throttle: reduce power_absorbed_cf from 1.55 to 1.40, one step at a time. If prop overspeeds: increase absorption modestly and check governor limits. If the aircraft is too hard to keep straight during takeoff: try rudder_effectiveness 1.10, with no more than one adjustment per test. If climb is too extreme or unreasonable: reduce power_scalar in steps, e.g. 2.90 -> 2.60 -> 2.30. If true power is low, test for custom engine-code override before adjusting. Use safe test conditions and start with half throttle. A real 1000 HP conversion is NOT plausibly achievable through common Bonanza STCs; this is experimental simulator tuning. Source references: MSFS 2020 SDK engines.cfg, flight_model.cfg documentation and basic aerodynamics guides. ENHANCED SPEED / STRUCTURAL ENVELOPE (2026-11-01) ================================================ THIS IS A SIMULATOR-ONLY HYPOTHETICAL REINFORCED EXPERIMENTAL RACER. No real-world STC or engineering substantiation for these limits is claimed. Updates made to modified/flight_model.cfg: - max_indicated_speed: 205 -> 225 KIAS (hypothetical reinforced-racer redline) - cruise_speed: 216 -> 255 knots (sim reference cruise speed, not Vno) - positive_g_limit_flaps_up: +4.4 -> +4.6 G - negative_g_limit_flaps_up: -1.7 -> -1.8 G - flap-down G limits: unchanged; high loads with flaps extended are unsafe - flap extension / gear speeds: unchanged - No change to flap configuration, stall speeds, aerodynamic lift, engine, or drag settings from previous mod. OPERATIONAL NOTES: - Vno / top of green arc is NOT defined by these flight_model.cfg changes. - Proposed 225 KIAS is NOT validated by the actual A36TC design or testing. - A real airframe would need flutter analysis/testing, structural reinforcement, redesigned attachment points, control balancing, and engine/propeller certification engineering. - A higher cruise_speed config value does not guarantee achievable real flight speeds. - At high altitude, true airspeed is higher at the same IAS; flutter/Mach margins matter. - MSFS gauges / custom Black Square avionics may still show original redlines. - Keep the original aircraft files and do not use this mod as real aircraft guidance.