BLACK SQUARE BONANZA A36TC - 1000 HP RACE / PROP GOVERNOR v3 ============================================================= INSTALLATION 1. Close Microsoft Flight Simulator 2020. 2. BACK UP the two config files in your installed Black Square A36TC aircraft. 3. Copy modified/engines.cfg and modified/flight_model.cfg to their matching installed location. Do not install the ZIP itself in Community. 4. If your installation requires a layout.json manifest, regenerate/update it for both modified files using an MSFS package-layout utility. 5. Restart MSFS. Restore the originals from your own backup if incompatible. WHAT WAS CHANGED * New conceptual 5-blade, 6.7-foot-diameter, high-solidity prop configuration. * Coarse-pitch limit 34.9 -> 55 degrees; cruise pitch 35.2 -> 39 degrees. * Governor pitch response 0.01 -> 1.2, PID changes, RPM minimum 1700. * propeller MOI 2.4 -> 3.8 to avoid unrealistic RPM snap. * Modern-prop power_absorbed_cf corrected from 1.55 to 0.90. SDK says 0-1. * Less artificial thrust_scalar: 1.37 -> 1.18. * Incremental aero cleanup, with meaningful drag and torque effects retained. * Climb reference 122 KIAS and cruise reference 265 KTAS. These are target references, not in-simulator proof of achieved performance. * Previous 225 KIAS simulated Vne and +4.6/-1.8 clean-G envelope retained. IMPORTANT LIMITS & REALISM * 1000 HP on an A36TC is a speculative, uncertified experimental conversion. These changes are for simulator play and do not correspond to a validated STC. * The physical model will not visually display five blades unless its model and animations are modified separately. * The 2700 RPM direct-drive arrangement with this much power remains highly unconventional. Prop diameter and ground clearance were not increased. * Fuel, temperatures, Black Square custom engine scripts and cockpit redlines may not follow native .cfg parameters. The Black Square 2020 Analog Bonanza and newer Bonanza Professional are distinct products; your supplied files appear to follow the earlier native cfg pattern. * Above about 18,000 ft, 250-280 KTAS can require operating near the 225-KIAS simulated redline; monitor KIAS, not only TAS. * Full-power takeoff / climb can overheat the original engine simulation and may consume fuel far faster than the stock instrumentation predicts. TEST PLAN (ISA / clear weather / no wind / fixed weight) A. Static full-power run: set prop max, open throttle smoothly, watch 2700 RPM. If RPM exceeds ~2750 persistently, STOP the test and reduce power. B. Full throttle climb at ~120 KIAS: note indicated RPM, governor setting, vertical speed, MP, and whether rudder travel reaches its stop. C. At 12k, 16k, 20k ft, stabilize and record KIAS, KTAS, RPM and % power. Reduce power if exceeding 225 KIAS or governor cannot hold RPM. D. Try prop commands 2700 -> 2500 -> 2300 RPM in level flight to confirm the controller actually commands coarse pitch rather than saturating. NEXT TUNING IF NEEDED * RPM still overshoots at max coarse pitch: more blade loading or smaller effective engine power scalar, not just higher PID gains. * RPM oscillates: reduce governor P to 22 and I to 2; D can remain 16. * RPM governor lags: increase prop_tc to 1.6 (make one change at a time). * 280+ KTAS or too quick: increase parasite_drag_scalar to 0.89. * Under 250 KTAS at high altitude: reduce parasite_drag_scalar to 0.83, without changing the 225-KIAS redline. * Overpowering yaw: reduce rudder scaling only after checking prop direction, rudder authority, and speed; p_factor_on_yaw stays 1. NO FLIGHT TEST PERFORMED: This is a testable starting calibration, NOT a verified flight model. Black Square may implement power/RPM via custom code.