# X-90T V3 changelog: Takeoff Asymmetry Recovery **Build:** V3.0 / 2026-11-16 | **Simulation:** Microsoft Flight Simulator 2020 ## Reported V2 test discrepancy - On rotation after takeoff acceleration, the X-90T rolled sharply left into a hangar, despite full available aileron and rudder. - This is the user's flight-simulator observation. No flight data trace is available to separate physical-style prop torque, P-factor yaw, propwash, control calibration, or the simulator's engine model. - P-factor creates yaw primarily, while engine/propeller torque creates roll. The latter may be amplified by the modern propeller model and full-strength roll scalars at the 3,000 SHP experimental target. ## Exact V2 -> V3 changes | File | Setting | V2 | V3 | Intent | |---|---|---:|---:|---| | engines.cfg | prop_mod_moment_scalar_roll | 1.00 | **0.14** | Reduce directly modeled modern-prop torque roll at high shaft torque | | engines.cfg | prop_mod_moment_scalar_yaw | 1.00 | **0.20** | Reduce modeled yaw moment | | flight_model.cfg | torque_on_roll | 1.00 | **0.20** | Reduce baseline engine torque roll tendency | | flight_model.cfg | p_factor_on_yaw | 1.00 | **0.30** | Reduce asymmetric blade loading yaw | | flight_model.cfg | engine_wash_on_roll | 1.00 | **0.35** | Reduce propwash-induced rolling moment | | flight_model.cfg | gyro_precession_on_roll | 1.00 | **0.60** | Moderate pitch/rotation related roll coupling | | flight_model.cfg | gyro_precession_on_yaw | 1.00 | **0.60** | Moderate pitch/rotation related yaw coupling | | flight_model.cfg | aileron_effectiveness | 1.00 | **1.10** | Small increment in roll control authority | | flight_model.cfg | rudder_effectiveness | 0.85 | **1.00** | Recover rudder authority previously reduced in stock tuning | | flight_model.cfg | rudder_maxangle_scalar | 0.60 | **0.70** | Minor increase within conventional V-tail scaler range | ## Preserved from V2 - Rated target 3,000 SHP, `maximum_torque=6500`, `torque_automatic_limit=7200`, 2,200 RPM operating target and governor PID 13/3/8. - Blade-pitch response, modeled absorbed-torque feedback, and stock four-blade visual propeller. - V2 custom turbine controller with RPM/ITT/torque fuel taper, 850 C ITT damage threshold and 2,300 RPM overspeed protection. - Stock fuel tanks, aircraft weight, speed envelope, 3D models, sound and cockpit layout. ## Flight-test interpretation This *simulator* patch reduces engine-induced moments to values intended to be more manageable without turning the aircraft into an instant-response arcade model. The same physical 3,000 SHP system would require major aerodynamic, structural and propulsion redesign. Settings have NOT been tested in flight. Do not assume any takeoff speed, angle, power, ITT limit or maneuver is safe for a real aircraft. ## Retest plan (MSFS only) 1. Start cold at a wide unobstructed field. Remove obstacles and use weather with zero wind. Verify full rudder and aileron movement and neutral controller calibration. 2. At standstill, slowly apply partial power and check for accelerating left roll/yaw or loss of heading. Record exact torque indication and prop RPM. 3. Abort the run if holding heading requires near full rudder or if wing drop appears at low speed. Never try to save a poor takeoff by accelerating through a control limit. 4. At modest torque, test directional control at increasing runway speeds without lifting off. Compare against stock turbine on same runway and loading. 5. On a new flight, rotate at a stable, lower-than-full-power setting. Observe control margin and climb before experimenting with higher power. 6. Only if the governor/ITT and directional control behave reliably, try a moderate-power climb and record torque, ITT, RPM, IAS, airspeed at rotation and max aileron/rudder used. 7. If left roll persists, share flight data or a short clip. It could be from a non-scalar engine force, controller issue or another custom model. Do not simply raise aileron effectiveness again. ## Installer and rollback - The ZIP contains the **actual CFG and XML replacement files**. The Windows `.cmd` auto-finds the installed `x90t-bonanza-experimental` and copies those three files, backing up the originals and `layout.json` to `Community\X90T_V3_BACKUP_`. - `ROLLBACK_X90T_V3.cmd` restores the newest V3 backup. Original Black Square and piston X-90 packages are not edited. - All files validated for XML/ZIP integrity and required configuration keys, but not tested in Windows or MSFS.