# Bonanza X-90T V4.0 - Thrust Recovery & Staged Power Rebuild Build: 2026-11-16 | Microsoft Flight Simulator 2020 | Simulator experimentation only. ## Why V4 is necessary Flight-test report: with the V1/V2 3,000 SHP experimental configuration, increasing the power lever beyond approximately 50% appeared to decrease aircraft airspeed. Earlier observations included uncontrolled left rolling tendency on rotation, turbine ITT over 850 C, and severe governor/prop-RPM abnormalities. These are user-reported simulator observations, not independently measured flight traces. A code review identified two plausible major causes: 1. V2 added a custom multiplicative fuel limiter that began reducing flow above **805 C indicated ITT**, **2200 indicated torque**, and **2220 propeller RPM**. At higher throttle, this could produce *less* delivered power. 2. V2 changed `prop_mod_use_absorbed_torque` from Black Square's 0 to 1 and expanded modeled prop blade area (aspect ratio 7 -> 4.5). This changes how modern-prop torque interacts with the turbine, potentially overloading the original four-blade/7-foot propeller model. A third contributing setting: V2's `RPM_on_TP_torque_table` reduced modeled torque to 50% at 3500 prop RPM, adding power loss after a governor overspeed. ## V3 -> V4 exact configuration changes | File | Key | V3 | V4 | Purpose | |---|---|---|---|---| | engines.cfg | `prop_mod_use_absorbed_torque` | `1` | `0` | Return to stock partial-modern prop/engine coupling for isolation | | engines.cfg | `prop_mod_aspect_ratio` | `4.5` | `7` | Restore stock effective blade geometry | | engines.cfg | `prop_mod_lift_slope_cf` | `3.35` | `3.15` | Restore stock propeller lift curve | | engines.cfg | `beta_max` | `68.0` | `59.5` | Restore stock maximum blade pitch | | engines.cfg | `prop_tc` | `0.80` | `0.35` | Controlled faster blade-pitch response than stock, slower than V2 | | engines.cfg | `prop_governor_p` | `13` | `5` | Restore Black Square stock governor P | | engines.cfg | `prop_governor_i` | `3` | `3` | Unchanged stock I | | engines.cfg | `prop_governor_d` | `8` | `15` | Restore Black Square stock governor D | | engines.cfg | `prop_governor_iboundary` | `120` | `100` | Restore stock integrator boundary | | engines.cfg | `prop_governor_dboundary` | `900` | `1000` | Restore stock derivative boundary | | engines.cfg | `RPM_on_TP_torque_table` | `1000:0.65, 1400:0.82, 1800:0.92, 2200:1.00, 2400:0.88, 2700:0.68, 3500:0.50` | `1000:0.72, 1400:0.88, 1800:0.96, 2200:1.00, 2400:0.98, 2700:0.91, 3500:0.72` | Gentler high-RPM derate, no 50% step at 3500 RPM | | engines.cfg | `high_fuel_flow` | `1250` | `950` | Align simulator fuel capacity with revised target | | engines.cfg | `fuel_flow_max` | `1250` | `950` | Align simulator fuel cap with revised target | | engines.cfg | `maximum_torque` | `6500` | `4000` | Stage shaft torque near 2,100 SHP at 2200 prop RPM | | engines.cfg | `torque_automatic_limit` | `7200` | `5200` | Smooth torque ceiling before 3000 SHP research | | engines.cfg | `rated_shaft_hp` | `3000` | `2200` | Temporary lower nameplate aligned with staged test power | | engines.cfg | `PowerSpecificFuelConsumption` | `0.42` | `0.43` | Initial Jet-A BSFC calibration for new power target | | Turbine_INT.xml | high-throttle fuel-target slope | `11.80` | `8.80` | Throttle fuel demand reaches roughly 950 lb/hr at 100% | | Turbine_INT.xml | custom V2 RPM/ITT/torque fuel limiter | Enabled | **Removed** | Eliminate reverse-power behavior from simultaneous derating | | Turbine_INT.xml | fuel command soft ceiling | 1250 lb/hr in V2 added limiter | **950 lb/hr** before original damage logic | Cap fuel while preserving monotonic commanded flow | ### Important, intentional power reduction The `rated_shaft_hp` field has changed from 3,000 to **2,200 SHP**. Under the MSFS turbine torque formula, the configured `maximum_torque=4000` multiplied by the stock density-on-torque table gives up to about **5,200 ft-lb** at sea-level density and 2,200 RPM before the cap. That is about **2,178 mechanical SHP** (5200*2200/5252), *if the sim reaches those conditions*. It is an **estimate from config**, not a measured engine dyno result or guaranteed MSFS performance. At lower prop RPM and changing density, output differs. We are temporarily sacrificing the 3,000 SHP target to test whether higher power lever inputs now produce increasing thrust. The original four-blade 7-ft Black Square prop model has not been physically validated for 3,000 SHP. ### Preserved - V3 reductions to simulated torque roll, P-factor yaw, modern-prop roll/yaw, and gyro/propwash moments. - V3 moderate aileron/rudder control effectiveness enhancements. - V1 Black Square damage thresholds: sustained ITT damage above **850 C**, overspeed and turbine damage logic remain. This is **not** approval to operate at those ITT levels. - V1 1/3 scaling of the custom torque indicator. Thus indicated torque is **not direct ft-lb**; a displayed 1,500 roughly represents 4,500 actual ft-lb before Black Square's other corrections. - Existing X-90T aircraft identity, cockpit instruments, model and textures, fuel configuration, original Black Square package, and piston X-90 untouched. ## How to install 1. Exit MSFS 2020. 2. Extract the complete installer ZIP. 3. Double-click `INSTALL_X90T_V4.cmd`. 4. Automatic folder detection searches your observed `E:\MSFS\Community` location and other paths; a folder chooser is a fallback. 5. A separate `X90T_V4_BACKUP_...` folder appears alongside the X-90T, then it replaces just three files and rebuilds `layout.json`. 6. To undo, close MSFS and run `ROLLBACK_X90T_V4.cmd`. ## First V4 diagnostics, simulator only On a clear day, with the same fuel load and configuration, start at ground idle with brakes set and use **brief, incremental** throttle applications at roughly 20%, 35%, 50%, and 65%; stop well before exceeding any indicated operating limits. Record prop RPM, actual ENG TORQUE (ft-lb if available via debug), Black Square indicated torque, ITT, Ng and FF, and whether brake-holding thrust grows with lever input. If RPM runs away or the engine loses power, report the first lever position at which it happens. Avoid takeoff until engine + governor response are predictable. After successful static tests, use moderate power on a long unobstructed runway and verify control margin *before* rotation. No actual MSFS simulator flight test, governor verification, or Windows PowerShell execution occurred during packaging. The files were syntax/structure and ZIP-checked only.