QUESTIONS FROM
THE HANGAR.
Practical answers about the mods, real-world plausibility, file editing, licensing, and exactly which problems remain unsolved.
No questions match that search.
PISTON MODDING
Does the X-90P really make 1,500 horsepower?
1,500 HP is the current nominal configuration target. The sim has not provided an independently verified brake-horsepower measurement, and the engine model contains custom multipliers. Treat the figure as an engineering target.
How fast has the piston version flown?
The pilot reported 290 KIAS at 15,000 ft. This is indicated airspeed, not true airspeed or groundspeed. It was not a standardized maximum-speed test with complete weather, aircraft mass, and calibration records.
Why is the boost only 45 inHg when earlier builds used 90?
The 90-inHg experiments caused major conflicts with the original simulated piston-engine damage logic. The team reduced the working full-boost setting to about 45 inHg to improve reliability.
What happened to the prop governor?
V3 of the piston governor solved a major overspeed issue. A later report noted an unusual roughly 60-second initial prop-cycle delay at 180°F oil, with subsequent cycles responding normally. That issue remains unresolved.
Are the 600-gallon tanks realistic?
Not as a bolt-on real Bonanza modification. The MSFS system uses 285-gallon simulated mains and 15-gallon tips per side. Real structural strength, tank volume, fuel-system design and CG limits would require extensive engineering.
Why did the fuel-flow estimate change?
An earlier reported full-boost burn was around 450 GPH. A later patch targeted roughly 130–150 GPH at nominal 1,500 HP using a revised specific fuel-consumption assumption and scalar. The final sustained in-sim flow has not yet been reported.
TURBINE MODDING
Why switch to a turbine at all?
A real high-output piston engine would face enormous cooling, detonation, component stress and maintenance challenges. A turbine is a more natural basis for sustained high power, though 3,000 SHP in a Bonanza still requires a completely hypothetical engine and airframe redesign.
Does the X-90T really deliver 3,000 SHP?
Not yet demonstrated. The engine configuration calls for a 3,000-SHP rating and higher torque capacity, but propeller and engine-system interactions caused poor V1 performance. V2 is an unverified recovery tune.
Why was V1 slower than the stock turbine?
The reported 3,500 RPM prop overspeed, unresponsive governor, high ITT and poor climb point to a mismatch between torque production, governor control and propeller loading. Adding shaft horsepower without a matched propeller can make the simulation behave worse.
What changed in V2?
V2 retunes the governor PID, dramatically increases modeled pitch-response speed, increases available blade pitch, enables modeled prop load feedback, tempers low-RPM torque, caps torque more tightly and adds experimental thermal/RPM fuel limiting.
Did V2 fix it?
There are not yet any reported V2 flight-test measurements. Its changes should be treated as test hypotheses, not as confirmed governor or performance fixes.
Is the eight-blade propfan installed?
No. The X-90T still uses the original four-blade visual prop and a modified four-blade simulation. A real swept-blade propfan would need new 3D geometry, aerodynamic data, integration and major airframe redesign.
Does the X-90T have the piston X-90’s 600 gallons?
No. V2 retained the stock Black Square B36TP fuel tank geometry. The source manual specifies 124 US gallons total. A future 600-gallon turbine system is only an idea, not an installed X-90T feature.
FILES, OWNERSHIP & HOSTING
Do I need to own Black Square Bonanza Professional?
Yes. These personal modding workflows are built on the commercially licensed Black Square Bonanza Professional files. The website does not distribute those files and is not a substitute for purchasing the add-on.
Are the piston X-90 and X-90T separate entries?
Yes. The installed projects have their own Community package folders and separate aircraft-selection entries. They are designed not to edit the original Black Square aircraft.
What can I edit in engines.cfg versus the custom cockpit XML?
The CFG files influence MSFS engine, fuel, propeller and flight-model parameters. Black Square’s separate XML model behaviors also calculate torque, ITT, controls, gauges and failures. Consistent changes often need both layers.
Can I upload the entire aircraft package for download?
Not without permission from its rightsholders. The commercial 3D models, textures, sounds and instruments remain their intellectual property. A public site should favor documentation, screenshots where permitted, and installation tooling that reads each user’s licensed local copy.
Can I publish photos and call everything fair use?
Fair use is a context-dependent legal defense in some jurisdictions, not a blanket license. We have deliberately used credited Creative Commons reference photos and one project-supplied simulator screenshot; screenshots of proprietary assets can still be subject to applicable copyright and publisher terms.
Is this safe or useful for a real aircraft?
No. These are speculative Microsoft Flight Simulator settings and research exercises. They do not establish real-world engine limits, structural safety, aircraft handling or airworthiness.
What is needed to host the website?
XAMPP with Apache is enough. Copy the unzipped folder into htdocs and visit http://localhost/x90-flight-test-lab/. The site uses plain HTML, CSS and JavaScript, no database or PHP.