FLIGHT OPERATIONS / X-90T / PUBLIC EDITION
RESEARCH BOARD NO. X90T-FTB-001 • 2026

THE FLIGHT
TEST BOARD.

A transparent look at how the X-90T is being tested. A disciplined, nine-phase plan adapted from experimental-aircraft practices for Microsoft Flight Simulator 2020.

PUBLIC / READ ONLY
74 TEST POINTS
09TEST PHASES
00PUBLISHED PASSES
00CARDS ASSESSED

No owner-published checklist snapshot yet.

◉ PUBLIC VIEWING MODESTATUS DATA: NOT PUBLISHEDVISITORS CANNOT EDIT OR SAVE RESULTS
01 / PURPOSE

MEASURE.
QUESTION.
REPEAT.

Each card defines a repeatable check. The program begins on the ground, proceeds through engine and propeller behavior, then expands to flight handling, altitude, speed, fuel and reliability.

These are planned checks, not certifications or evidence that the X-90T passed them. Any published outcomes appear with a clear date and status.

CURRENT EXPERIMENT / X-90T V2

Governor recovery

V1 was substantially slower than the stock turbine, climbed at roughly 1,000 ft/min and exhibited governor malfunction and high ITT. V4 now removes the experimental fuel limiter and stages output down for repeat testing. Its performance has not yet been independently confirmed by a new submitted flight report.

Review X-90T V2 changes ↗
02 / KNOWN DISCREPANCIES

THE V1 FINDINGS.

These are reported simulator observations, not completed pass/fail statuses for the individual test cards.

FT-OBS / 01~1,000 FPM

Climb performance

Reported climb rate in the V1 3,000-SHP-target build, worse than the stock turbine.

FT-OBS / 02850+ °C

Interstage temperature

ITT reportedly exceeded 850°C during testing. This is not an approved operating limit.

FT-OBS / 03NO CONTROL

Propeller governor

The pilot reported that the governor was not functioning, with poor propeller power transfer.

FT-OBS / 042,500+ IND.

Torque indication

Reported indicated torque exceeded 2,500 on the rescaled V1 instrument. Actual shaft ft-lb were not verified.

03 / THE TEST PROGRAM

NINE PHASES. 74 CHECKS.

Open a phase to inspect every individual test. These are read-only records. An empty status means no official result has been published.

P0Before the first engine runTest plan & configuration8 CHECKS
Objective

Freeze a reproducible baseline, define simulation limits and a stop plan.

ENTRY CONDITIONS

Simulator closed; V1 installer complete.

EXIT CONDITIONS

Known configuration recorded and test-day limits selected.

P0-01

Verify aircraft identity

NOT PUBLISHED

Select X-90T V1 in MSFS; ensure the stock turbine and piston X-90 remain separate.

P0-02

Freeze software baseline

NOT PUBLISHED

Record simulator version, X-90T build, weather preset, assistance settings and active mods.

P0-03

Verify V1 file presence

NOT PUBLISHED

Confirm engine and turbine cockpit XML replacements were installed in the X-90T only.

P0-04

Choose a test area

NOT PUBLISHED

Use a long runway, calm/clear weather and generous virtual terrain clearance; avoid AI traffic.

P0-05

Document mass and CG

NOT PUBLISHED

Record weight, CG position, fuel aboard and payload in the MSFS weight-and-balance interface.

P0-06

Define operating hold points

NOT PUBLISHED

Write down the stock displayed limits and conservative test-day caps before attempting high power.

P0-07

Plan abort and recovery

NOT PUBLISHED

Choose when to reject a run, reduce power, land, reload and note a failure.

P0-08

Establish a repeatable measurement method

NOT PUBLISHED

Decide which values come from cockpit instruments versus DevMode/debug tools; note any gauge scaling doubts.

P1Ground card G-01Powerplant & ground checks9 CHECKS
Objective

Confirm engine response, propeller control, fuel delivery and safe simulated handling.

ENTRY CONDITIONS

P0 complete; parking brake and runway environment suitable.

EXIT CONDITIONS

Repeatable ground response without unexplained exceedances.

P1-01

Cold start baseline

NOT PUBLISHED

Start from cold-and-dark and capture start time, peak ITT, Ng behavior and stabilization.

P1-02

Idle stabilization

NOT PUBLISHED

Record stabilized idle ITT, Ng, Np, oil indications and fuel flow.

P1-03

Propeller and beta/reverse check

NOT PUBLISHED

At the appropriate stock procedure power settings, confirm prop control and beta/reverse behave predictably.

P1-04

Power-lever mapping

NOT PUBLISHED

Record torque/ITT/Ng/Np/FF at idle, low, intermediate and higher settings; advance gradually.

P1-05

Instrument consistency

NOT PUBLISHED

Compare digital and analog turbine indications, watching for pegged or misleading needles.

P1-06

Transient response

NOT PUBLISHED

Make small power changes and record delay, overshoot and oscillation.

P1-07

Fuel and electrical systems

NOT PUBLISHED

Verify tanks/selector/quantity, alternator, annunciators and fuel-flow behavior.

P1-08

Low-speed taxi

NOT PUBLISHED

Check brakes, steering, ground idle thrust, turning, and stopping margin.

P1-09

Shutdown and hot restart

NOT PUBLISHED

Check orderly shutdown, spool-down, restart ITT response and repeatability.

P2Flight card F-01First flight: basic airworthiness8 CHECKS
Objective

Establish basic controllability and a predictable return to landing.

ENTRY CONDITIONS

P1 passed. Calm daylight, conservative weight, moderate power and no high-speed experimentation.

EXIT CONDITIONS

Normal takeoff, climb, turns, approach and landing documented without unexpected behavior.

P2-01

Preflight and departure brief

NOT PUBLISHED

Record runway/weather, takeoff weight/CG, power target and virtual abort/return plan.

P2-02

Takeoff acceleration and tracking

NOT PUBLISHED

Use a conservative power setting and log directional control, liftoff IAS and surprises.

P2-03

Initial climb checks

NOT PUBLISHED

Record IAS, VSI, torque, ITT, Ng, Np and whether engine parameters stay stable.

P2-04

Trim and straight-and-level

NOT PUBLISHED

Check level flight, trim range, pitch stability and any unexplained control input.

P2-05

Gentle turns

NOT PUBLISHED

Check shallow left/right turns, coordination and control feel at comfortable IAS.

P2-06

Power change at altitude

NOT PUBLISHED

Reduce/reapply moderate power; record pitch and yaw changes and governor behavior.

P2-07

Approach and configuration

NOT PUBLISHED

Check gear/flaps under stock operating limits, speed stability and sink-rate response.

P2-08

Land, secure and debrief

NOT PUBLISHED

Document touchdown IAS, braking and all anomalies before starting another test card.

P3Flight card F-02Turbine, governor & 3,000 SHP claim9 CHECKS
Objective

Check whether the 3,000 SHP target is actually delivered and controllable.

ENTRY CONDITIONS

F-01 clean; known test-day instrument limits and enough altitude to recover from anomalies.

EXIT CONDITIONS

Engine map and governor response recorded with no unexplained runaway.

P3-01

Stabilize at test altitude

NOT PUBLISHED

Record pressure altitude, OAT, KIAS, TAS, weight and fuel before each point.

P3-02

25% power test point

NOT PUBLISHED

At a stable condition, record torque, ITT, Ng, Np, FF and acceleration.

P3-03

50% power test point

NOT PUBLISHED

Repeat at same reference condition; record turbine response and prop RPM.

P3-04

75% power test point

NOT PUBLISHED

Check increasing torque, fuel flow and ITT; note whether prop absorbs power.

P3-05

Brief high-power point

NOT PUBLISHED

Only after earlier points are normal, briefly test the highest planned *sim-only* setting; back out on instability.

P3-06

Governor transient check

NOT PUBLISHED

Record RPM droop, overshoot, hunting and recovery during controlled power changes.

P3-07

Turbine thermal behavior

NOT PUBLISHED

Record peak/stabilized ITT and whether simulated cooling recovers after reducing power.

P3-08

Fuel-flow plausibility

NOT PUBLISHED

Compare observed GPH to model output and indicate units; note whether FF is capped.

P3-09

Power verification

NOT PUBLISHED

If true shaft torque (ft-lb) and RPM are available, compute SHP; a normalized cockpit torque gauge is not a direct ft-lb reading.

P4Flight card F-03Handling & controllability8 CHECKS
Objective

Characterize stability, trim authority and power-induced handling changes.

ENTRY CONDITIONS

F-01/F-02 acceptable; operate within the known low/mid-speed region.

EXIT CONDITIONS

Repeatable behavior in common configurations with no unexplained control reversal.

P4-01

Trim authority

NOT PUBLISHED

Document pitch and rudder trim at stable IAS and different power settings.

P4-02

Pitch response

NOT PUBLISHED

Apply small elevator inputs and record overshoot/settling.

P4-03

Roll and yaw response

NOT PUBLISHED

Perform gentle control inputs; note asymmetric behavior or unusual coupling.

P4-04

Power-induced yaw/roll

NOT PUBLISHED

Record required rudder and bank corrections as torque increases.

P4-05

Configuration transitions

NOT PUBLISHED

Record gear/flap changes only within the aircraft’s displayed limits.

P4-06

Approach-to-landing handling

NOT PUBLISHED

Perform simulated approach and go-around at conservative weight/power.

P4-07

Slow flight observation

NOT PUBLISHED

At generous altitude, observe low-speed trim/handling without forcing unapproved stall/spin testing.

P4-08

Repeat at another CG

NOT PUBLISHED

Adjust loading in MSFS and confirm a second weight/CG combination remains controllable.

P5Flight card F-04Climb, cruise & performance map8 CHECKS
Objective

Measure a reproducible power-speed-altitude relationship.

ENTRY CONDITIONS

Stable engine and normal handling. One variable at a time.

EXIT CONDITIONS

Climb and level-flight data points recorded and repeatable.

P5-01

Establish reference cruise

NOT PUBLISHED

Choose a fixed altitude, weight, weather and power setting.

P5-02

Climb segment A

NOT PUBLISHED

Record start/end altitude, elapsed time, IAS, weight, ITT, torque, Ng, Np and FF.

P5-03

Climb segment B

NOT PUBLISHED

Repeat at higher altitude if engine and aircraft remain stable; compare rate of climb.

P5-04

Level-off and stabilize

NOT PUBLISHED

At each cruise altitude, allow airspeed and engine readings to settle.

P5-05

Cruise speed point 1

NOT PUBLISHED

Log KIAS, KTAS, Mach, FF and torque at a repeatable moderate setting.

P5-06

Cruise speed point 2

NOT PUBLISHED

Log the same quantities at a higher *approved test-day* setting.

P5-07

Altitude sweep

NOT PUBLISHED

Repeat only at altitudes already shown to be controllable; do not assume 35,000 ft is achievable.

P5-08

Repeatability run

NOT PUBLISHED

Fly the same point again; note performance drift, temperature sensitivity or inconsistent engine data.

P6Flight card F-05 · simulator research onlySpeed-envelope expansion8 CHECKS
Objective

Identify speed-dependent behaviors without confusing simulation survivability with structural validation.

ENTRY CONDITIONS

Engine, low/mid-speed handling and flight model reviewed. Any beyond-stock-limit test is explicitly simulator-only.

EXIT CONDITIONS

A documented maximum simulated speed with stability and instrument observations.

P6-01

Record published/model limits

NOT PUBLISHED

Identify the stock airspeed/structural limits and distinguish them from the fictional X-90T limits.

P6-02

Select a conservative first IAS point

NOT PUBLISHED

Start in a previously demonstrated speed range, not at a maximum-speed attempt.

P6-03

Stabilize and document

NOT PUBLISHED

At a steady point, record KIAS, KTAS, Mach, altitude, power, controls, trim and fuel.

P6-04

Expand incrementally in the simulator

NOT PUBLISHED

Use small IAS changes with a distinct data point at each step; stop on abnormal behavior.

P6-05

Observe pitch/roll/yaw response

NOT PUBLISHED

Record trim shifts, oscillations, buffet and unexpected control sensitivity.

P6-06

Monitor prop/engine limits

NOT PUBLISHED

Watch Np, Ng, torque, ITT and fuel flow at high flight speed.

P6-07

Differentiate IAS vs TAS vs Mach

NOT PUBLISHED

Report all three: dynamic pressure, speed through air and compressibility are not interchangeable.

P6-08

Hold point and debrief

NOT PUBLISHED

Stop the session at the first questionable point; record limit exceedances rather than calling them cleared.

P7Flight card F-06Fuel, weight, systems & endurance8 CHECKS
Objective

Characterize fuel burn, mass/CG changes and sustained operation.

ENTRY CONDITIONS

Reliable engine and predictable handling at conservative cruise.

EXIT CONDITIONS

Fuel-use and endurance data documented across loading conditions.

P7-01

Verify turbine tank configuration

NOT PUBLISHED

Record actual X-90T capacity and locations; do not assume it inherited the piston X-90’s 600-gallon modification.

P7-02

Fuel quantity consistency

NOT PUBLISHED

Compare cockpit gauges with the MSFS fuel/weight menu at full, intermediate and low quantities.

P7-03

Timed cruise burn

NOT PUBLISHED

Record start fuel, end fuel, elapsed time, power and simulator-reported fuel flow.

P7-04

Compare observed vs computed burn

NOT PUBLISHED

Calculate gallons used per hour; log any large difference from indicated GPH.

P7-05

Weight and CG sweep

NOT PUBLISHED

Use different virtual loadouts and recheck takeoff/landing trim and handling.

P7-06

Sustained thermal run

NOT PUBLISHED

Observe ITT, oil and torque stability over a controlled longer cruise segment.

P7-07

System operation check

NOT PUBLISHED

Check lights, electric bus, navigation/autopilot and turbine-related cockpit controls.

P7-08

Repeat engine start and shutdown

NOT PUBLISHED

Look for failures or changing behavior after extended operation.

P8Postflight engineering cardDebrief, fixes & release gate8 CHECKS
Objective

Convert observations into tracked issues and a controlled next build.

ENTRY CONDITIONS

At least one ground or flight card conducted.

EXIT CONDITIONS

Test result exported, issues prioritized, and the next build decision documented.

P8-01

Export test data

NOT PUBLISHED

Export JSON and CSV before modifying aircraft files.

P8-02

Log discrepancies

NOT PUBLISHED

For each anomaly, record reproduction steps and whether it is intermittent.

P8-03

Classify issue severity

NOT PUBLISHED

Separate stop-testing engine/control failures from indication errors and cosmetic issues.

P8-04

Verify clean baseline

NOT PUBLISHED

Repeat a known-good point before changing any CFG or XML.

P8-05

Change one major variable at a time

NOT PUBLISHED

Document exact file changes and new build ID for each tuning iteration.

P8-06

Regression test

NOT PUBLISHED

After each modification, repeat start, idle, torque/gov test and reference cruise.

P8-07

Generate mini-AOH

NOT PUBLISHED

Summarize demonstrated simulated performance; distinguish tested limits from targets and guesses.

P8-08

Release gate

NOT PUBLISHED

Record pass / hold / revise decision for X-90T V2, not a real-world airworthiness declaration.

PUBLIC TEST RECORDTest cards and status reports are presented for reference. Published results cannot be edited from this page.
04 / TEST DISCIPLINE

GO. HOLD. STOP.

GO

Previous test objectives met; predictable turbine and propeller response; credible measurements and documented test limits.

HOLD

Incomplete prerequisites, uncertain torque-gauge calibration or unexplained engine behavior. Resolve before expanding the simulator envelope.

STOP

Runaway governor, uncontrollable oscillation, rising ITT, uncommanded control response or repeatable model failure. Terminate the test point and document the condition.

WHY THE POWER NUMBER NEEDS PROOF

3,000 SHP is a target.

Estimated shaft horsepower requires independently meaningful shaft torque and RPM, not simply the indicated Black Square torque value.

SHP = (ft-lb × RPM) ÷ 5,252

In V1, the torque display was rescaled. Until that scaling is validated, a cockpit indication cannot establish actual shaft horsepower.


Methodology: Inspired by FAA AC 90-89C and task-based experimental flight testing. This is not an airworthiness approval or an operating manual for a real aircraft.

NEXT / TEST SESSION

THE DATA COMES NEXT.

Governor response, stabilized ITT, torque, propeller RPM, climb rate and cruise performance remain the key measurements for the V4 evaluation. Results will be added as testing progresses.

Back to the X-90T ↗