DEVELOPMENT CHANGELOGS.
A revision-controlled record of the piston and turbine experiments: package intent, specific setting changes, pilot observations and unresolved discrepancies.
EVERY CONFIGURATION HAS A HISTORY.
The records below were assembled from the original project installer archives. These are simulator development entries, not approved design records. A packaged release is not necessarily flight-tested.
X-90P / PISTON DEVELOPMENT.
Click any revision to expand its original accompanying documentation.
P-011000 HP race-engine foundationInitial piston output uplift; initial propeller and aero research. Engine/controller performance not independently demonstrated.EXPAND +
Source package: Bonanza_A36TC_1000HP_Race_Experimental.zip · Read source documentation ↗
BLACK SQUARE A36TC | 1000 HP EXPERIMENTAL RACE CONCEPT | MSFS 2020 INSTALL 1. Exit MSFS. Back up your full aircraft package, especially any layout.json. 2. Find the specific Black Square A36TC SimObjects/Airplanes/<variant> folder that currently contains the two original CFG files (use a file content comparison to confirm). 3. Replace ONLY that folder's engines.cfg and flight_model.cfg with the files from modified/. 4. If your install uses a layout.json file, it may require regenerating to register changed file sizes (especially for Community packages); use a trusted MSFS layout generator. 5. Launch and test at a low fuel load in clear weather. Use gradual throttle, full rudder available, and monitor RPM, speed, temperatures and directional control. Restore originals/ to revert. WHAT WAS CHANGED ENGINE: rated engine HP 300 -> 1000, power scalar 0.87 -> 2.90. MSFS's power scalar changes net torque; the rated-HP number itself does NOT guarantee true output. 3 -> 4 prop blades, power absorption coefficient 1.30 -> 1.55, prop inertia 1.6 -> 2.4, a modest prop lift tweak. HANDLING: rudder area 14.5 -> 16.2 sq ft, effectiveness 0.85 -> 1.03, rudder deflection scalar 0.60 -> 0.72, rudder lift 1.30 -> 1.38, yaw stability 1.0 -> 1.1 and roll stability 0.8 -> 0.9. P-factor, prop torque and gyro effects all remain 1.0 rather than being artificially removed. AERO: drag_coef_zero_lift 0.0300 -> 0.0280; parasite_drag_scalar 0.920 -> 0.865; Oswald efficiency 0.65 -> 0.72; induced_drag_scalar 1.15 -> 1.10. UNCHANGED: Vne/max indicated speed, maximum gross weight, G limits, wing area, stall tables, fuel capacity and other safety-related values. REALISM AND LIMITATIONS This is a fictional, extreme experimental race build, NOT an actual approved STC, physically validated Bonanza performance model, or an airworthy design. A 1000-HP Bonanza would require major structural, cooling, fuel-system, drivetrain, propeller and flutter work. The 4-blade prop and enlarged rudder are approximations in the flight model; no 3D geometry or artwork is changed. Drag changes represent conceptual fairings, sealing, surface finishing and cleanup, not certified measured reductions. The extra engine power may be overridden by Black Square's custom engine code, which is not included in the supplied files. 1000 HP and climb rate cannot be guaranteed without in-sim tests. Existing 205 KIAS limit remains; overspeed is still possible and must be avoided. TUNING AFTER TEST FLIGHT If RPM bogs badly at wide-open throttle: reduce power_absorbed_cf from 1.55 to 1.40, one step at a time. If prop overspeeds: increase absorption modestly and check governor limits. If the aircraft is too hard to keep straight during takeoff: try rudder_effectiveness 1.10, with no more than one adjustment per test. If climb is too extreme or unreasonable: reduce power_scalar in steps, e.g. 2.90 -> 2.60 -> 2.30. If true power is low, test for custom engine-code override before adjusting. Use safe test conditions and start with half throttle. A real 1000 HP conversion is NOT plausibly achievable through common Bonanza STCs; this is experimental simulator tuning. Source references: MSFS 2020 SDK engines.cfg, flight_model.cfg documentation and basic aerodynamics guides.
P-02Enhanced envelopeExtended handling, drag, and climb-configuration research.EXPAND +
Source package: Bonanza_A36TC_1000HP_Race_Enhanced_Envelope.zip · Read source documentation ↗
BLACK SQUARE A36TC | 1000 HP EXPERIMENTAL RACE CONCEPT | MSFS 2020 INSTALL 1. Exit MSFS. Back up your full aircraft package, especially any layout.json. 2. Find the specific Black Square A36TC SimObjects/Airplanes/<variant> folder that currently contains the two original CFG files (use a file content comparison to confirm). 3. Replace ONLY that folder's engines.cfg and flight_model.cfg with the files from modified/. 4. If your install uses a layout.json file, it may require regenerating to register changed file sizes (especially for Community packages); use a trusted MSFS layout generator. 5. Launch and test at a low fuel load in clear weather. Use gradual throttle, full rudder available, and monitor RPM, speed, temperatures and directional control. Restore originals/ to revert. WHAT WAS CHANGED ENGINE: rated engine HP 300 -> 1000, power scalar 0.87 -> 2.90. MSFS's power scalar changes net torque; the rated-HP number itself does NOT guarantee true output. 3 -> 4 prop blades, power absorption coefficient 1.30 -> 1.55, prop inertia 1.6 -> 2.4, a modest prop lift tweak. HANDLING: rudder area 14.5 -> 16.2 sq ft, effectiveness 0.85 -> 1.03, rudder deflection scalar 0.60 -> 0.72, rudder lift 1.30 -> 1.38, yaw stability 1.0 -> 1.1 and roll stability 0.8 -> 0.9. P-factor, prop torque and gyro effects all remain 1.0 rather than being artificially removed. AERO: drag_coef_zero_lift 0.0300 -> 0.0280; parasite_drag_scalar 0.920 -> 0.865; Oswald efficiency 0.65 -> 0.72; induced_drag_scalar 1.15 -> 1.10. UNCHANGED: Vne/max indicated speed, maximum gross weight, G limits, wing area, stall tables, fuel capacity and other safety-related values. REALISM AND LIMITATIONS This is a fictional, extreme experimental race build, NOT an actual approved STC, physically validated Bonanza performance model, or an airworthy design. A 1000-HP Bonanza would require major structural, cooling, fuel-system, drivetrain, propeller and flutter work. The 4-blade prop and enlarged rudder are approximations in the flight model; no 3D geometry or artwork is changed. Drag changes represent conceptual fairings, sealing, surface finishing and cleanup, not certified measured reductions. The extra engine power may be overridden by Black Square's custom engine code, which is not included in the supplied files. 1000 HP and climb rate cannot be guaranteed without in-sim tests. Existing 205 KIAS limit remains; overspeed is still possible and must be avoided. TUNING AFTER TEST FLIGHT If RPM bogs badly at wide-open throttle: reduce power_absorbed_cf from 1.55 to 1.40, one step at a time. If prop overspeeds: increase absorption modestly and check governor limits. If the aircraft is too hard to keep straight during takeoff: try rudder_effectiveness 1.10, with no more than one adjustment per test. If climb is too extreme or unreasonable: reduce power_scalar in steps, e.g. 2.90 -> 2.60 -> 2.30. If true power is low, test for custom engine-code override before adjusting. Use safe test conditions and start with half throttle. A real 1000 HP conversion is NOT plausibly achievable through common Bonanza STCs; this is experimental simulator tuning. Source references: MSFS 2020 SDK engines.cfg, flight_model.cfg documentation and basic aerodynamics guides. ENHANCED SPEED / STRUCTURAL ENVELOPE (2026-11-01) ================================================ THIS IS A SIMULATOR-ONLY HYPOTHETICAL REINFORCED EXPERIMENTAL RACER. No real-world STC or engineering substantiation for these limits is claimed. Updates made to modified/flight_model.cfg: - max_indicated_speed: 205 -> 225 KIAS (hypothetical reinforced-racer redline) - cruise_speed: 216 -> 255 knots (sim reference cruise speed, not Vno) - positive_g_limit_flaps_up: +4.4 -> +4.6 G - negative_g_limit_flaps_up: -1.7 -> -1.8 G - flap-down G limits: unchanged; high loads with flaps extended are unsafe - flap extension / gear speeds: unchanged - No change to flap configuration, stall speeds, aerodynamic lift, engine, or drag settings from previous mod. OPERATIONAL NOTES: - Vno / top of green arc is NOT defined by these flight_model.cfg changes. - Proposed 225 KIAS is NOT validated by the actual A36TC design or testing. - A real airframe would need flutter analysis/testing, structural reinforcement, redesigned attachment points, control balancing, and engine/propeller certification engineering. - A higher cruise_speed config value does not guarantee achievable real flight speeds. - At high altitude, true airspeed is higher at the same IAS; flutter/Mach margins matter. - MSFS gauges / custom Black Square avionics may still show original redlines. - Keep the original aircraft files and do not use this mod as real aircraft guidance.
P-03Governor V3Conceptual 5-blade/6.7-ft prop; pitch limit 34.9° to 55°; pitch response 0.01 to 1.2; tuned governor and modern-prop absorption. User reported major improvement.EXPAND +
Source package: Bonanza_A36TC_1000HP_Race_PropGovernor_v3.zip · Read source documentation ↗
BLACK SQUARE BONANZA A36TC - 1000 HP RACE / PROP GOVERNOR v3 ============================================================= INSTALLATION 1. Close Microsoft Flight Simulator 2020. 2. BACK UP the two config files in your installed Black Square A36TC aircraft. 3. Copy modified/engines.cfg and modified/flight_model.cfg to their matching installed location. Do not install the ZIP itself in Community. 4. If your installation requires a layout.json manifest, regenerate/update it for both modified files using an MSFS package-layout utility. 5. Restart MSFS. Restore the originals from your own backup if incompatible. WHAT WAS CHANGED * New conceptual 5-blade, 6.7-foot-diameter, high-solidity prop configuration. * Coarse-pitch limit 34.9 -> 55 degrees; cruise pitch 35.2 -> 39 degrees. * Governor pitch response 0.01 -> 1.2, PID changes, RPM minimum 1700. * propeller MOI 2.4 -> 3.8 to avoid unrealistic RPM snap. * Modern-prop power_absorbed_cf corrected from 1.55 to 0.90. SDK says 0-1. * Less artificial thrust_scalar: 1.37 -> 1.18. * Incremental aero cleanup, with meaningful drag and torque effects retained. * Climb reference 122 KIAS and cruise reference 265 KTAS. These are target references, not in-simulator proof of achieved performance. * Previous 225 KIAS simulated Vne and +4.6/-1.8 clean-G envelope retained. IMPORTANT LIMITS & REALISM * 1000 HP on an A36TC is a speculative, uncertified experimental conversion. These changes are for simulator play and do not correspond to a validated STC. * The physical model will not visually display five blades unless its model and animations are modified separately. * The 2700 RPM direct-drive arrangement with this much power remains highly unconventional. Prop diameter and ground clearance were not increased. * Fuel, temperatures, Black Square custom engine scripts and cockpit redlines may not follow native .cfg parameters. The Black Square 2020 Analog Bonanza and newer Bonanza Professional are distinct products; your supplied files appear to follow the earlier native cfg pattern. * Above about 18,000 ft, 250-280 KTAS can require operating near the 225-KIAS simulated redline; monitor KIAS, not only TAS. * Full-power takeoff / climb can overheat the original engine simulation and may consume fuel far faster than the stock instrumentation predicts. TEST PLAN (ISA / clear weather / no wind / fixed weight) A. Static full-power run: set prop max, open throttle smoothly, watch 2700 RPM. If RPM exceeds ~2750 persistently, STOP the test and reduce power. B. Full throttle climb at ~120 KIAS: note indicated RPM, governor setting, vertical speed, MP, and whether rudder travel reaches its stop. C. At 12k, 16k, 20k ft, stabilize and record KIAS, KTAS, RPM and % power. Reduce power if exceeding 225 KIAS or governor cannot hold RPM. D. Try prop commands 2700 -> 2500 -> 2300 RPM in level flight to confirm the controller actually commands coarse pitch rather than saturating. NEXT TUNING IF NEEDED * RPM still overshoots at max coarse pitch: more blade loading or smaller effective engine power scalar, not just higher PID gains. * RPM oscillates: reduce governor P to 22 and I to 2; D can remain 16. * RPM governor lags: increase prop_tc to 1.6 (make one change at a time). * 280+ KTAS or too quick: increase parasite_drag_scalar to 0.89. * Under 250 KTAS at high altitude: reduce parasite_drag_scalar to 0.83, without changing the 225-KIAS redline. * Overpowering yaw: reduce rudder scaling only after checking prop direction, rudder authority, and speed; p_factor_on_yaw stays 1. NO FLIGHT TEST PERFORMED: This is a testable starting calibration, NOT a verified flight model. Black Square may implement power/RPM via custom code.
P-04High-subsonic research baselineExperimental drag, airspeed and structural-envelope edits. Targets are not validated flight limits.EXPAND +
Source package: Bonanza_X90_Phase1_Transonic_Research_Baseline.zip · Read source documentation ↗
BONANZA X-90 | TRANSONIC RESEARCH AIRFRAME | PHASE 1 EXPERIMENTAL CFG This is an early test envelope, NOT a Mach 0.90-capable finished aircraft. The V3 engine file has been copied UNCHANGED, so its governor settings remain intact. The V3 piston/prop cannot realistically propel a Bonanza to M0.90. Changed in flight_model.cfg: - Raised simulated Mach/IAS ceilings for researching high-speed flight. - Added illustrative increasing compressibility drag through M0.9. - Reduced aerodynamic control authority with higher indicated speed. - Changed reference speeds. These DO NOT deliver additional engine power. NOT INCLUDED: jet propulsion, redesigned wing geometry/3D model, cabin pressurization, working transonic flight certification, custom Mach-limit annunciations. These deliberately require a later airframe/propulsion development and in-sim testing. INSTALL FOR TESTING ONLY: 1) Keep your working V3 backup and save your original flight_model.cfg. 2) Close MSFS. 3) Copy the test flight_model.cfg into the EXACT aircraft folder your V3 uses. 4) Keep your working V3 engines.cfg IN PLACE. Do NOT overwrite it with another engine file unless restoring V3. 5) If MSFS uses a package layout.json, regenerate entries/sizes/dates for edited files with your SDK packaging process or known package layout tool. 6) Test at benign speeds first, then in incremental level-flight steps. Expect unrealistically high load limits and flight-model artifacts. 7) To undo, restore the V3 flight_model.cfg from its existing backup. This prototype's 330-KIAS setting is NOT a real-world safe Vne. The unaltered Bonanza 3D model and structural assumptions do not represent a transonic airframe.
P-05High-boost engine / flight modelEscalated nominal power and expanded turbo behavior, supporting development of the fictional race engine.EXPAND +
Source package: Bonanza_X90_HighBoost_Engine_FlightModel_Tune_Windows.zip · Read source documentation ↗
BONANZA X-90 - HIGH BOOST ENGINE / FLIGHT MODEL TUNE V2 This is a two-file update for the X-90 90 inHg / 35,000 ft / 400-gallon build. It is NOT a full aircraft or turbo logic installer. Requirements: - Existing Black Square Bonanza Professional installation with the X-90 90-inHg turbo XML patch already installed. - Compatible engines.cfg and flight_model.cfg (this patch replaces both). - Close MSFS 2020 before installing. Install (NO PYTHON): 1. Extract all ZIP contents to a folder, not the Windows ZIP preview. 2. Double-click INSTALL_X90_POWER_TUNE.cmd. 3. Select the package ROOT with layout.json and manifest.json. 4. Type INSTALL and press Enter. 5. Backups are created in X90_Backups under the selected folder. WHAT CHANGED: - power_scalar 2.90 -> 3.30 (approx 13.8% torque scaling increase; not a measured HP rating). - max_rated_hp 1000 -> 1500 nominal, primarily rated/consumption parameter; not itself an output power multiplier. - Higher fuel consumption and somewhat improved cooling assumptions. - Heavier 5,800 lb hypothetical structure and 2,550 lb empty weight. - More rudder area/authority at low speed, damped high-speed controls and stability. - Previous optimistic parasite drag reduction scaled back slightly. - 400-gallon fuel configuration and 90 inHg 35k targets preserved. - Existing PROPELLER and governor settings untouched. - Existing Black Square custom turbo XML NOT modified by this update. - Existing X90 boost gauge / cockpit model NOT modified by this update. IMPORTANT: Extremely fictional aircraft. No real Bonanza structure, engine, or piston propeller can be assumed safe/credible at Mach 0.9, 90 inHg and the high weight. Reference speed changes do not validate structural safety. Due to custom Black Square turbo and prop systems, delivered MAP, HP, and RPM MUST be checked in MSFS. Start at reduced throttle, then test progressively while monitoring governor/RPM, MAP, CHT, oil and fuel flow. If overspeed occurs, revert. Rollback: restore engines.cfg, flight_model.cfg, and layout.json from the new timestamped X90_Backups folder.
P-0690 inHg / 35,000 ft / 400 gal experimentHigh-boost research configuration. Target manifold pressure 90 inHg, 35,000-ft critical-altitude ambition, 400-gal research tankage.EXPAND +
Source package: Bonanza_X90_90inHg_35000ft_400gal_Windows_Installer.zip · Read source documentation ↗
BONANZA X-90 | NO-PYTHON WINDOWS INSTALLER 1. Close MSFS 2020. 2. Extract ALL files from this ZIP into a folder on your PC. Do not run the installer from inside the ZIP preview. 3. Double-click INSTALL_X90.cmd. 4. Select the Black Square Bonanza PACKAGE ROOT containing manifest.json and layout.json. Do not select SimObjects/Airplanes. 5. Type INSTALL when prompted. 6. The installer copies the 3 patched files and updates layout.json. Backups are saved under X90_Backups in the package. No Python installation is required; the script uses Windows PowerShell, included with Windows 11. If Windows warns about executing unknown scripts, inspect the source before proceeding. Do not run as administrator unless your aircraft installation requires it. Rollback: restore the three matching files and layout.json from your latest X90_Backups/<timestamp> folder. This installer targets the exact same X-90 90-inHg / 35,000-ft / 400-gallon configuration as the previous package. It does NOT include the pressurization mod. All performance values are experimental simulation targets, not demonstrated aircraft capabilities. Test in simulator.
P-0745 inHg engine retuneReduced maximum manifold pressure to about 45 inHg to reduce excessive modeled overboost.EXPAND +
Source package: Bonanza_X90_45inHg_Engine_Only_Windows.zip · Read source documentation ↗
BONANZA X-90 - 45 inHg MANIFOLD PRESSURE - ENGINE ONLY ======================================================= This patch changes ONLY engines.cfg from the prior X-90 High-Boost Engine & Flight Model Tune. Design goal: 45 inHg manifold pressure (ABSOLUTE) at full throttle from sea level to 35,000 ft. - max_design_mp = 45.0 - critical_altitude = 35000 - 1,500 HP nominal, power_scalar 3.30, and the full propeller/governor block are untouched. - No gauges, panel files, cockpit models, flight_model.cfg, or pressurization content included. IMPORTANT: 'At all times' has been interpreted as maintaining up to 45 inHg at FULL THROTTLE through 35,000 feet, NOT fixing manifold pressure at idle or partial throttle. LIMITATION: Black Square's separate custom turbocharger behavior code lives in model.base/BonanzaProfessional_Base_INT.XML. This engine-only patch does NOT modify that file. If your earlier 35,000-foot turbo XML patch is not installed, 45 inHg at altitude may NOT be achievable, even when engines.cfg is set as requested. The stock Black Square gauge can also be limited by its own display range. Verify with an external SimVar reader if necessary. WINDOWS INSTALLATION (NO PYTHON) 1. Close MSFS 2020 and make a backup of your aircraft package. 2. Extract this ZIP to a folder. 3. Double-click INSTALL_X90_45INHG.cmd. 4. Choose the Black Square PACKAGE ROOT with layout.json and manifest.json. 5. Type INSTALL to confirm. Automatic backups are saved under X90_Backups. If you are currently running the old 90 inHg X-90 package but NOT the later 1,500 HP tune, this package will also install the later 1,500 HP engine configuration. It is built from that most recent supplied tune, not from your live simulator installation. UNTESTED: The installer and engine model have not been verified in the simulator. This is a fictional experimental configuration, not a real aircraft performance claim.
P-0845 inHg durability protectionRaised overboost-damage reference from 32 to 48 inHg, retained temperature/failure protections; CHT and oil-cooling coefficients revised.EXPAND +
Source package: Bonanza_X90_45inHg_Durability_Fix_NoPython.zip · Read source documentation ↗
BONANZA X-90 - 45 INHG DURABILITY PATCH (EXPERIMENTAL) Close MSFS, extract the ZIP, double click INSTALL_X90_DURABILITY.cmd and select the Black Square package ROOT (contains layout.json). Type INSTALL. No Python. PATCHED IN PLACE (backs up originals): - engines.cfg: CHT cooling constant raised to at least 0.90, oil cooling to at least 0.30 - model.base/BonanzaProfessional_Base_INT.XML: manifold overboost damage reference 32 -> 48 inHg, ignition normalization 42 -> 50 inHg - layout.json: updates affected paths sizes/timestamps UNCHANGED: V3 governor/propeller, X90 boost target, turbo critical altitude, fuel tanks, flight_model.cfg, panels, gauges. WHY: At 45 inHg, the stock 32 inHg damage expression adds damage every second, eventually resulting in failure. The replacement maintains pressure overshoot damage above 48 inHg and all existing high CHT, EGT, oil temperature, prop RPM, fire and shock-cooling protections. A separate CHT > 215 C seizing condition remains and can still cause failure. This is a fictional race-engine simulation, not a real safe operating limit or verified fix in MSFS. Check performance/temperatures in flight. If the installation says the reference cannot be found, stop: your Black Square cockpit XML differs from the supplied version or is already modified. Do not force replacement. To roll back, restore engines.cfg, BonanzaProfessional_Base_INT.XML and layout.json from the folder shown by the installer inside X90_Backups.
P-09Standalone X-90P aircraftCreated independent aircraft-selection package; original stock Bonanza retained.EXPAND +
Source package: Bonanza_X90_Separate_Aircraft_NoPython_Windows.zip · Read source documentation ↗
BONANZA X-90 EXPERIMENTAL - SEPARATE AIRCRAFT INSTALLER ========================================================== WHAT THIS DOES - Creates a NEW 'x90-bonanza-experimental' package inside your MSFS 2020 Community folder. - Does NOT change files inside the original Black Square package. - Copies the installed Black Square airplane assets (textures, sound, models, configurations) into the new package. - Replaces the new aircraft's aircraft.cfg with one uniquely titled "X-90 Experimental Bonanza N5172C" variant. - Replaces only the new copy's engines.cfg and flight_model.cfg with X-90 45 inHg / 1500 HP-class config. - Restores clean gauge-free cockpit 3D files from uploads made before the failed boost-gauge experiments. - Modifies only the new copy's engine-damage pressure thresholds: 32 -> 48 inHg and ignition reference 42 -> 50 inHg; preserves the original prop governor from the user's working X-90 configuration. - Leaves 400 gallons of fuel and prior X-90 handling/structural changes from included flight model. - Creates a new layout.json/manifest.json in the new package. IMPORTANT LIMITATIONS - The base Black Square Bonanza Professional installation must remain installed to provide its global html_ui gauges. - If the ORIGINAL Black Square package already has earlier X-90 patches installed, THIS installer does NOT revert them. Restore your ORIGINAL aircraft package using the backups made by earlier installers or reinstall Black Square first. The new X-90 will be separate; the stock original may not be stock until restored. - This is experimental and UNTESTED inside MSFS. Some avionics and custom systems may depend on package identity or global L: variables and require follow-up fixes. - Because all airplane assets are locally copied, expect several gigabytes additional disk usage. No symbolic links or hardlinks; source unchanged. - No pressurization panel and no boost gauge in the forked model. - The X-90 governor setting is retained from the previous 45 inHg engine configuration, but no promise that it can hold RPM at all powers is implied. - Turbo actual performance at 35,000 ft is still controlled by Black Square's complex XML logic and needs flight testing. INSTALLATION (NO PYTHON) 1) Quit MSFS 2020. 2) Extract this complete ZIP to its own folder. 3) Double-click INSTALL_X90_SEPARATE.cmd. 4) Select the existing Black Square PACKAGE ROOT, usually named bksq-aircraft-bonanzapro, containing manifest.json and layout.json. 5) Select the MSFS 2020 Community folder (NOT the Black Square folder). 6) Type CREATE and press Enter. 7) Restart MSFS and look for manufacturer "X-90 Experimental" and type "Bonanza X-90". UNINSTALL Close MSFS. Delete Community/x90-bonanza-experimental. The original Black Square aircraft is unaffected by the new installer. IF THE AIRCRAFT DOES NOT SHOW - Ensure the package is directly inside Community, not nested in an extra folder. - Make sure original Black Square is still installed. - If you see a _STAGING folder, installation did not finish; remove the staging folder and retry. - Send the visible installer output and the location of the Community folder. This build is hypothetical simulation modification, not a flight-certified airframe.
P-10Fuel and mass V1 / direct replacement285 gal main + 15 gal tip per side: 600 gal. 7,000-lb fictional MTOW. Target 130–150 GPH at actual 1,500 HP; analog face markings remain outdated.EXPAND +
Source package: Bonanza_X90_600gal_Direct_Files_Installer_FIXED.zip · Read source documentation ↗
X-90 FUEL TUNE: REAL REPLACEMENT FILES, NOT TEXT PATCHING 1. CLOSE MSFS 2020. 2. Extract the entire ZIP to a folder outside Community. 3. Double-click INSTALL_X90_REPLACEMENTS.cmd (no Python). 4. Enter the complete path to your Community\x90-bonanza-experimental folder. 5. Type REPLACE. Backups are created alongside the X-90 package. FILES INCLUDED: REPLACEMENT_FILES\SimObjects\Airplanes\x90-aircraft-bonanza\engines.cfg REPLACEMENT_FILES\SimObjects\Airplanes\x90-aircraft-bonanza\flight_model.cfg REPLACEMENT_FILES\SimObjects\Airplanes\x90-aircraft-bonanza\model.base\BonanzaProfessional_Base_INT.XML The first two are the literal edited CFG files you requested. The XML file changes Black Square's proportional main fuel gauge needle range and fuel-flow needle scale. You can inspect every file in Notepad before installation. CHANGES: 285 gal LEFT MAIN + 15 gal LEFT TIP, 285 gal RIGHT MAIN + 15 gal RIGHT TIP (600 gal total); main and tip longitudinal coordinates set to 0.15 ft. Max gross 7000 lb is ONLY a hypothetical sim limit, not a real-world safe load. 600 gal of avgas alone weighs about 3600 lb. Flight test mass/CG is necessary. Engine fuel_flow_scalar 0.34, best-power SFC 0.55 lb/hp/hr target; aiming 130-150 GPH at 1500 actual hp, NOT guaranteed. Engine and cooling tune, 45 inHg pressure target and V3 governor settings inherited from the prior separate X-90 package. XML keeps high-boost durability references and 35,000 ft turbo target. LIMITATION: Existing gauge FACE PAINTED NUMBERS STILL READ STOCK. Main fuel needles represent fraction full with a 285-gallon calibration; printed 40-gallon labels are not accurate. The fuel flow gauge analog scale is also not repainted. For actual gallons/GPH, use sim instrumentation or MSFS fuel window until face art is corrected. WARNING: This is a full replacement of 3 specific files based on the last X-90 aircraft package generated in this conversation. If you manually edited those files since installation, those edits will be replaced. The installer backs them up. The external boost-gauge mod may also have edited the cockpit XML; this replacement can supersede those changes. The stock Black Square package is not touched. MANUAL COPY OPTION: copy the 3 files from REPLACEMENT_FILES to the equivalent folders within Community\x90-bonanza-experimental, then update the three paths' size and date entries in layout.json; otherwise MSFS may not recognize modified files. The Windows installer performs the layout update for you.
P-11Optional boost-gauge experimentsAttempts to add a live 3D boost indicator. Visual visibility not confirmed; this is an experimental, unverified feature, not a released success.EXPAND +
Source package: Bonanza_X90_Boost_Gauge_Separate_Aircraft_v3_Windows.zip · Read source documentation ↗
BONANZA X-90 BOOST GAUGE V3 - SEPARATE AIRCRAFT TARGET FIX Why this version: The earlier gauge installers were aimed at the stock bksq-aircraft-bonanzapro package. The separate X-90 installer restored an unmodified cockpit model, so the gauge meshes were absent from the separate aircraft even if you installed the original gauge patch. WHAT THIS PATCH DOES: - Targets ONLY Community/x90-bonanza-experimental - Adds the virtual cockpit gauge panel section under panel.N5172C - Copies the X90Boost HTML gauge assets into the X-90 package - Replaces the separate X-90 interior glTF and matching binary with the prior gauge prototype - Backs up modified files and rebuilds layout.json - DOES NOT change engine, turbo, flight_model.cfg, governor, tanks, or stock Black Square files INSTALL: 1. Close MSFS 2020. 2. Extract the ZIP to a normal folder. 3. Double-click INSTALL_X90_GAUGE_V3.cmd (no Python). 4. Choose the x90-bonanza-experimental folder in Community, not the stock Black Square package. 5. Type INSTALL. 6. Start MSFS and load the separate Bonanza X-90. STATUS: The installer paths and embedded gauge assets have been checked, but this remains an UNTESTED cockpit gauge prototype. A mesh added to an already compiled/optimized MSFS glTF may still require rebuilding through the MSFS SDK. If the gauge does not appear, STOP reapplying position patches. Instead we need an MSFS SDK model rebuild from source or a supported instrument mounted on an existing screen. The location is an estimate and may still be occluded. This change does not alter MAP. ROLLBACK: The installer creates X90_Gauge_Backup_<timestamp> in the X-90 package folder. With MSFS closed, restore files from the backup preserving their relative paths. Remove the three added files from html_ui/.../x90-bonanza/X90Boost if needed. Rebuild layout.json if removing files; easiest is to restore the backed-up layout.json. Do not point this installer at the stock Black Square package.
X-90T / TURBINE DEVELOPMENT.
Click any revision to expand its original accompanying documentation.
T-00Separate turbine cloneWorking separate aircraft package; one-click installation issue fixed at installer v3. Original remains installed.EXPAND +
Source package: Bonanza_X90T_V1_3000SHP_ONE_CLICK_FULL_INSTALLER_FIXED_v3.zip · Read source documentation ↗
X-90T Experimental V1 - 3,000 SHP Turbine Changelog
Based on the uploaded stock Black Square turbine engines(2).cfg and BonanzaProfessional_Turbine_INT.xml. No stock package files are changed by this installer.
| Item | Stock | V1 | Rationale |
|---|---|---|---|
| Rated shaft power | 500 SHP | 3,000 SHP | Display target only; not direct physical power parameter |
| Engine maximum torque (physical model) | 1,200 ft-lb | 6,200 ft-lb | Along with altitude multipliers produces enough shaft torque for ~3,000 SHP |
| Automatic torque cap (physical model) | 5,000 ft-lb | 7,500 ft-lb | ~3,141 SHP cap at 2,200 RPM; necessary for 3,000 SHP target |
| Black Square indicated torque | Actual ft-lb | 1/3 actual ft-lb | Keeps doubled cockpit protection threshold usable; printed dial markings no longer accurate |
| Indicated torque damage onset | 1,250 | 2,500 normalized units | Exactly double the prior Black Square threshold; equivalent 7,500 actual ft-lb |
| Sustained ITT damage threshold | 715 C | 850 C | Hypothetical high-temp turbine limit; damage logic retained |
| Severe ITT damage threshold | 1,090 C | 1,250 C | Severe exceedance still accumulates damage |
| Turbine fuel-control full throttle commanded flow | 370 lb/hr | 1,320 lb/hr | Allows ~3,000 SHP class fuel feed |
| Engine high-fuel-flow and max fuel-flow parameters | 350 lb/hr | 1,350 lb/hr | Keeps engine-side model aligned with custom controller |
| Power-specific fuel consumption | 0.365 | 0.42 lb/SHP/hr | Roughly 1,260 lb/hr at 3,000 SHP, before sim-specific scaling |
| Oil cooling constant | 0.20 | 0.27 | Modest additional simulated oil cooling |
| Governor / gearbox / blade count | Stock | Unchanged | No unproven high RPM change; propeller may be bottleneck |
| Flight model / fuel tanks / airframe limits | Stock | Unchanged | Explicitly out of scope for V1 |
Engineering limitations
- The user's requested doubling of torque limits is implemented on the Black Square indicated torque scale (1250 to 2500). In real simulated shaft torque, doubling the original 1200 ft-lb is insufficient for 3000 SHP at ~2200 prop RPM. A 7500 ft-lb ceiling is therefore required.
- The simulated ITT limit is not evidence that a real PT6-family hot section could survive 850 C continuously.
- The unmodified 4-blade propeller, governor and gearbox may not absorb the new torque; RPM overspeed is possible.
- Changing rated_shaft_hp alone does not increase actual simulated power.
- At full power, a 124-gallon stock fuel load might last well under an hour depending on fuel demand.
- The system may model only partial torque despite increased tables, and visual gauge scales may mislead. Verify with external data readouts.
T-01V1 / 3,000 SHP targetRated output 500→3,000 SHP target; max torque 1,200→6,200 ft-lb; cap 5,000→7,500; ITT damage 715→850°C; fuel delivery and cooling increased.EXPAND +
Source package: Bonanza_X90T_V1_3000SHP_NoPython_Replacement_Installer.zip · Read source documentation ↗
X-90T Experimental V1 - 3,000 SHP Turbine Changelog
Based on the uploaded stock Black Square turbine engines(2).cfg and BonanzaProfessional_Turbine_INT.xml. No stock package files are changed by this installer.
| Item | Stock | V1 | Rationale |
|---|---|---|---|
| Rated shaft power | 500 SHP | 3,000 SHP | Display target only; not direct physical power parameter |
| Engine maximum torque (physical model) | 1,200 ft-lb | 6,200 ft-lb | Along with altitude multipliers produces enough shaft torque for ~3,000 SHP |
| Automatic torque cap (physical model) | 5,000 ft-lb | 7,500 ft-lb | ~3,141 SHP cap at 2,200 RPM; necessary for 3,000 SHP target |
| Black Square indicated torque | Actual ft-lb | 1/3 actual ft-lb | Keeps doubled cockpit protection threshold usable; printed dial markings no longer accurate |
| Indicated torque damage onset | 1,250 | 2,500 normalized units | Exactly double the prior Black Square threshold; equivalent 7,500 actual ft-lb |
| Sustained ITT damage threshold | 715 C | 850 C | Hypothetical high-temp turbine limit; damage logic retained |
| Severe ITT damage threshold | 1,090 C | 1,250 C | Severe exceedance still accumulates damage |
| Turbine fuel-control full throttle commanded flow | 370 lb/hr | 1,320 lb/hr | Allows ~3,000 SHP class fuel feed |
| Engine high-fuel-flow and max fuel-flow parameters | 350 lb/hr | 1,350 lb/hr | Keeps engine-side model aligned with custom controller |
| Power-specific fuel consumption | 0.365 | 0.42 lb/SHP/hr | Roughly 1,260 lb/hr at 3,000 SHP, before sim-specific scaling |
| Oil cooling constant | 0.20 | 0.27 | Modest additional simulated oil cooling |
| Governor / gearbox / blade count | Stock | Unchanged | No unproven high RPM change; propeller may be bottleneck |
| Flight model / fuel tanks / airframe limits | Stock | Unchanged | Explicitly out of scope for V1 |
Engineering limitations
- The user's requested doubling of torque limits is implemented on the Black Square indicated torque scale (1250 to 2500). In real simulated shaft torque, doubling the original 1200 ft-lb is insufficient for 3000 SHP at ~2200 prop RPM. A 7500 ft-lb ceiling is therefore required.
- The simulated ITT limit is not evidence that a real PT6-family hot section could survive 850 C continuously.
- The unmodified 4-blade propeller, governor and gearbox may not absorb the new torque; RPM overspeed is possible.
- Changing rated_shaft_hp alone does not increase actual simulated power.
- At full power, a 124-gallon stock fuel load might last well under an hour depending on fuel demand.
- The system may model only partial torque despite increased tables, and visual gauge scales may mislead. Verify with external data readouts.
T-02V2 / governor recoveryPitch response 0.075→0.80, P/I/D 5/3/15→13/3/8, blade geometry and absorbed-torque feedback modified; custom fuel limiting was added.EXPAND +
Source package: Bonanza_X90T_V2_Governor_Recovery_OneClick_Installer.zip · Read source documentation ↗
X-90T V2 | Propeller/Engine Control Recovery | Experimental
Build: V2.0, 2026-11-16. Applies to: installed standalone x90t-bonanza-experimental (V1). Simulator: MSFS 2020.
Why V2 exists
V1 flight testing reported worse-than-stock acceleration, sluggish controls, ~1,000 fpm climb, indicated torque above 2,500, ITT above 850 C, propeller RPM reportedly up to ~3,500, and a non-responsive governor. These are reported observations, not measured/verified engine-model calculations. V1 applied six times the original turbine's horsepower demand without redesigning the stock four-bladed propeller or tuning its controller.
Changes (V1 -> V2)
| Area | V1 | V2 | Reason |
|---|---|---|---|
| Rated shaft power | 3,000 SHP | 3,000 SHP | Retain program target. Delivered shaft HP unverified. |
| Maximum modeled torque | 6,200 ft-lb | 6,500 ft-lb | Small torque-curve change, not an indiscriminate power increase. |
| Hard torque cap | 7,500 ft-lb | 7,200 ft-lb | At 2,200 RPM, 7,200 ft-lb is ~3,016 shaft HP; reduce runaway torque. |
| Torque versus prop RPM | 1,400 RPM: 1.43×; 2,200: 1.0× | 1,400: 0.82×; 1,800: 0.92×; 2,200: 1.0×; 2,400: 0.88×; 2,700: 0.68× | Remove V1's high low-RPM torque multiplication and taper torque above design RPM. |
| Modern prop absorbed-torque feedback | Off | On | Allow simulated prop aerodynamic load to feed back into engine. May require further tuning. |
| Blade aspect ratio (modeled) | 7.0 | 4.5 | Wider blade chord to absorb greater shaft power. Four blades remain visibly and logically modeled. |
| Prop lift-slope coefficient | 3.15 | 3.35 | Slightly more propeller aerodynamic authority. |
| Maximum blade pitch | 59.5° | 68° | Larger pitch authority for high torque. |
| Prop pitch response constant | 0.075 | 0.80 | Much faster blade-pitch response. MSFS docs indicate larger prop_tc changes pitch faster. |
| Governor PID P/I/D | 5 / 3 / 15 | 13 / 3 / 8 | Stronger proportional response with less derivative braking. |
| Governor I/D boundaries | 100 / 1000 | 120 / 900 | Support new response. |
| Turbine high/max fuel flow | 1,350 lb/hr | 1,250 lb/hr | Trim feed and reduce thermal spikes. |
| Black Square power-lever fuel factor | 12.50 | 11.80 | Full throttle target ~1,250 lb/hr rather than ~1,320. |
| Added engine fuel limiting | None | RPM / ITT / torque limiter | Taper command when prop >2,220 RPM, ITT >805 C, or V1-normalized torque >2,200. The limit becomes stronger as the overage increases. |
| Torque caution annunciator (normalized gauge) | 1,210 (stock threshold, mismatched) | 2,200 | Rescale caution to current X-90T torque gauge. |
| ITT caution annunciator | 705 C in-flight | 805 C | Match experimental prelimit caution; failure threshold remains 850 C. |
| Elevator and aileron elasticity | Stock, 150 KIAS: 0.60 | 0.84 / 0.82 at 150 KIAS | Restore some control authority without removing high-speed softening. |
| Rudder elasticity | Stock, 150 KIAS: 0.50 | 0.78 at 150 KIAS | Reduce simulated sluggishness. |
| Pitch and roll damping | -300 / -1.5 | -255 / -1.30 | Modest responsiveness improvement. |
| Engine damage thresholds | ITT 850 C, normalized torque 2,500, overspeed 2,300 RPM | Unchanged | Maintain failure simulation. |
| Four-blade 3D prop / gearbox / fuel tanks | Stock geometry | Unchanged | No unsupported 8-blade value, no new physical mesh, no fuel/CG edits. |
Important technical limits
- 3000 SHP is an unverified target, not a promise of actual output. The stock 4-blade propeller and 84-inch diameter are severe limitations. Realistically absorbing 3,000 SHP would require major prop/airframe redesign.
- MSFS 2020's documented
propeller_bladessetting supports 2, 3, or 4. No unsupported eight-blade trick is used. - Torque indication is V1 normalized to one third of modeled shaft torque. A displayed 2,200 means about 6,600 modeled ft-lb (before other display modifiers), and a displayed 2,500 approaches 7,500 modeled ft-lb. Printed gauge markings are still not certified or recalibrated.
- Custom fuel limiting is simulated engine protection, not a real-world turbine control system. Its effectiveness and stability must be tested. The high ITT condition may persist due to Black Square's custom temperature equations.
- The governor's min RPM, gearing, and external prop model were retained from the stock Black Square version because changing them blindly risks further breakage.
- No claim is made that altered airframe dynamics are physically valid or safe in a real aircraft.
Installation & rollback
- Close MSFS 2020. Extract this ZIP anywhere on your Windows PC.
- Double-click
INSTALL_X90T_V2.cmd. It should locateE:\MSFS\Community\x90t-bonanza-experimentalautomatically. Otherwise select that package folder. - The installer backs up all 4 affected files (
engines.cfg,flight_model.cfg, interior XML,layout.json) under a timestampedX90T_V2_BACKUP_...folder beside the aircraft package, then copies 3 replacement files, rebuilds the layout, and checks the result. - If V2 causes trouble, double-click
ROLLBACK_X90T_V2.cmdto restore the newest V2 backup and its original layout. - The original Black Square
bksq-aircraft-bonanzaproand pistonx90-bonanza-experimentalare never modified.
V2 flight-test card (sim only)
- Reset/restart the simulator aircraft after installation. Use a modest fuel load to compare V1 and V2 fairly.
- Ground run: cycle prop at conservative torque first. Verify responsive governor, normal pitch movement, and no >2300 RPM excursion.
- Climb at moderate power. Record actual observed prop RPM, ITT, normalized torque, Ng, KIAS, fuel flow, altitude, and vertical speed.
- Increase to 75%, then 90% power only if stable. If prop exceeds 2300 RPM, ITT 850 C, or torque 2500 normalized, abort that test, reduce power, and note values. Do not treat V2's limits as certified real-aircraft operating limits.
- Full-power testing only after the governor is stable. If the governor still fails at part power, stop and share measurements. It may require an MSFS prop-model change or reverting engine loading further.
Verification scope
- Source V1 and stock uploads were examined and changed keys were validated.
- Replacement XML parses as XML; ZIP integrity and file paths are checked.
- NOT tested on Windows/MSFS; power, handling, cooling, and governor claims are hypotheses until the user's next in-sim run.
T-03V3 / takeoff asymmetryAfter severe left roll on rotation, prop and engine asymmetry scalars reduced and control effectiveness revised; not flight-tested before V4.EXPAND +
Source package: Bonanza_X90T_V3_Takeoff_Stability_OneClick_Installer.zip · Read source documentation ↗
X-90T V3 changelog: Takeoff Asymmetry Recovery
Build: V3.0 / 2026-11-16 | Simulation: Microsoft Flight Simulator 2020
Reported V2 test discrepancy
- On rotation after takeoff acceleration, the X-90T rolled sharply left into a hangar, despite full available aileron and rudder.
- This is the user's flight-simulator observation. No flight data trace is available to separate physical-style prop torque, P-factor yaw, propwash, control calibration, or the simulator's engine model.
- P-factor creates yaw primarily, while engine/propeller torque creates roll. The latter may be amplified by the modern propeller model and full-strength roll scalars at the 3,000 SHP experimental target.
Exact V2 -> V3 changes
| File | Setting | V2 | V3 | Intent |
|---|---|---|---|---|
| engines.cfg | prop_mod_moment_scalar_roll | 1.00 | 0.14 | Reduce directly modeled modern-prop torque roll at high shaft torque |
| engines.cfg | prop_mod_moment_scalar_yaw | 1.00 | 0.20 | Reduce modeled yaw moment |
| flight_model.cfg | torque_on_roll | 1.00 | 0.20 | Reduce baseline engine torque roll tendency |
| flight_model.cfg | p_factor_on_yaw | 1.00 | 0.30 | Reduce asymmetric blade loading yaw |
| flight_model.cfg | engine_wash_on_roll | 1.00 | 0.35 | Reduce propwash-induced rolling moment |
| flight_model.cfg | gyro_precession_on_roll | 1.00 | 0.60 | Moderate pitch/rotation related roll coupling |
| flight_model.cfg | gyro_precession_on_yaw | 1.00 | 0.60 | Moderate pitch/rotation related yaw coupling |
| flight_model.cfg | aileron_effectiveness | 1.00 | 1.10 | Small increment in roll control authority |
| flight_model.cfg | rudder_effectiveness | 0.85 | 1.00 | Recover rudder authority previously reduced in stock tuning |
| flight_model.cfg | rudder_maxangle_scalar | 0.60 | 0.70 | Minor increase within conventional V-tail scaler range |
Preserved from V2
- Rated target 3,000 SHP,
maximum_torque=6500,torque_automatic_limit=7200, 2,200 RPM operating target and governor PID 13/3/8. - Blade-pitch response, modeled absorbed-torque feedback, and stock four-blade visual propeller.
- V2 custom turbine controller with RPM/ITT/torque fuel taper, 850 C ITT damage threshold and 2,300 RPM overspeed protection.
- Stock fuel tanks, aircraft weight, speed envelope, 3D models, sound and cockpit layout.
Flight-test interpretation
This simulator patch reduces engine-induced moments to values intended to be more manageable without turning the aircraft into an instant-response arcade model. The same physical 3,000 SHP system would require major aerodynamic, structural and propulsion redesign. Settings have NOT been tested in flight. Do not assume any takeoff speed, angle, power, ITT limit or maneuver is safe for a real aircraft.
Retest plan (MSFS only)
- Start cold at a wide unobstructed field. Remove obstacles and use weather with zero wind. Verify full rudder and aileron movement and neutral controller calibration.
- At standstill, slowly apply partial power and check for accelerating left roll/yaw or loss of heading. Record exact torque indication and prop RPM.
- Abort the run if holding heading requires near full rudder or if wing drop appears at low speed. Never try to save a poor takeoff by accelerating through a control limit.
- At modest torque, test directional control at increasing runway speeds without lifting off. Compare against stock turbine on same runway and loading.
- On a new flight, rotate at a stable, lower-than-full-power setting. Observe control margin and climb before experimenting with higher power.
- Only if the governor/ITT and directional control behave reliably, try a moderate-power climb and record torque, ITT, RPM, IAS, airspeed at rotation and max aileron/rudder used.
- If left roll persists, share flight data or a short clip. It could be from a non-scalar engine force, controller issue or another custom model. Do not simply raise aileron effectiveness again.
Installer and rollback
- The ZIP contains the actual CFG and XML replacement files. The Windows
.cmdauto-finds the installedx90t-bonanza-experimentaland copies those three files, backing up the originals andlayout.jsontoCommunity\X90T_V3_BACKUP_<timestamp>. ROLLBACK_X90T_V3.cmdrestores the newest V3 backup. Original Black Square and piston X-90 packages are not edited.- All files validated for XML/ZIP integrity and required configuration keys, but not tested in Windows or MSFS.
T-04V4 / thrust recoveryAfter reported decreasing airspeed beyond ~50% throttle, reversed the custom V2 fuel limiter, restored stock prop absorption/geometry and PID, staged nominal output to 2,200 SHP while retaining roll/yaw adjustments. Still untested.EXPAND +
Source package: Bonanza_X90T_V4_Thrust_Recovery_OneClick_Installer.zip · Read source documentation ↗
Bonanza X-90T V4.0 - Thrust Recovery & Staged Power Rebuild
Build: 2026-11-16 | Microsoft Flight Simulator 2020 | Simulator experimentation only.
Why V4 is necessary
Flight-test report: with the V1/V2 3,000 SHP experimental configuration, increasing the power lever beyond approximately 50% appeared to decrease aircraft airspeed. Earlier observations included uncontrolled left rolling tendency on rotation, turbine ITT over 850 C, and severe governor/prop-RPM abnormalities. These are user-reported simulator observations, not independently measured flight traces.
A code review identified two plausible major causes:
- V2 added a custom multiplicative fuel limiter that began reducing flow above 805 C indicated ITT, 2200 indicated torque, and 2220 propeller RPM. At higher throttle, this could produce less delivered power.
- V2 changed
prop_mod_use_absorbed_torquefrom Black Square's 0 to 1 and expanded modeled prop blade area (aspect ratio 7 -> 4.5). This changes how modern-prop torque interacts with the turbine, potentially overloading the original four-blade/7-foot propeller model.
A third contributing setting: V2's RPM_on_TP_torque_table reduced modeled torque to 50% at 3500 prop RPM, adding power loss after a governor overspeed.
V3 -> V4 exact configuration changes
| File | Key | V3 | V4 | Purpose |
|---|---|---|---|---|
| engines.cfg | prop_mod_use_absorbed_torque |
1 |
0 |
Return to stock partial-modern prop/engine coupling for isolation |
| engines.cfg | prop_mod_aspect_ratio |
4.5 |
7 |
Restore stock effective blade geometry |
| engines.cfg | prop_mod_lift_slope_cf |
3.35 |
3.15 |
Restore stock propeller lift curve |
| engines.cfg | beta_max |
68.0 |
59.5 |
Restore stock maximum blade pitch |
| engines.cfg | prop_tc |
0.80 |
0.35 |
Controlled faster blade-pitch response than stock, slower than V2 |
| engines.cfg | prop_governor_p |
13 |
5 |
Restore Black Square stock governor P |
| engines.cfg | prop_governor_i |
3 |
3 |
Unchanged stock I |
| engines.cfg | prop_governor_d |
8 |
15 |
Restore Black Square stock governor D |
| engines.cfg | prop_governor_iboundary |
120 |
100 |
Restore stock integrator boundary |
| engines.cfg | prop_governor_dboundary |
900 |
1000 |
Restore stock derivative boundary |
| engines.cfg | RPM_on_TP_torque_table |
1000:0.65, 1400:0.82, 1800:0.92, 2200:1.00, 2400:0.88, 2700:0.68, 3500:0.50 |
1000:0.72, 1400:0.88, 1800:0.96, 2200:1.00, 2400:0.98, 2700:0.91, 3500:0.72 |
Gentler high-RPM derate, no 50% step at 3500 RPM |
| engines.cfg | high_fuel_flow |
1250 |
950 |
Align simulator fuel capacity with revised target |
| engines.cfg | fuel_flow_max |
1250 |
950 |
Align simulator fuel cap with revised target |
| engines.cfg | maximum_torque |
6500 |
4000 |
Stage shaft torque near 2,100 SHP at 2200 prop RPM |
| engines.cfg | torque_automatic_limit |
7200 |
5200 |
Smooth torque ceiling before 3000 SHP research |
| engines.cfg | rated_shaft_hp |
3000 |
2200 |
Temporary lower nameplate aligned with staged test power |
| engines.cfg | PowerSpecificFuelConsumption |
0.42 |
0.43 |
Initial Jet-A BSFC calibration for new power target |
| Turbine_INT.xml | high-throttle fuel-target slope | 11.80 |
8.80 |
Throttle fuel demand reaches roughly 950 lb/hr at 100% |
| Turbine_INT.xml | custom V2 RPM/ITT/torque fuel limiter | Enabled | Removed | Eliminate reverse-power behavior from simultaneous derating |
| Turbine_INT.xml | fuel command soft ceiling | 1250 lb/hr in V2 added limiter | 950 lb/hr before original damage logic | Cap fuel while preserving monotonic commanded flow |
Important, intentional power reduction
The rated_shaft_hp field has changed from 3,000 to 2,200 SHP. Under the MSFS turbine torque formula, the configured maximum_torque=4000 multiplied by the stock density-on-torque table gives up to about 5,200 ft-lb at sea-level density and 2,200 RPM before the cap. That is about 2,178 mechanical SHP (52002200/5252), *if the sim reaches those conditions. It is an estimate from config, not a measured engine dyno result or guaranteed MSFS performance. At lower prop RPM and changing density, output differs.
We are temporarily sacrificing the 3,000 SHP target to test whether higher power lever inputs now produce increasing thrust. The original four-blade 7-ft Black Square prop model has not been physically validated for 3,000 SHP.
Preserved
- V3 reductions to simulated torque roll, P-factor yaw, modern-prop roll/yaw, and gyro/propwash moments.
- V3 moderate aileron/rudder control effectiveness enhancements.
- V1 Black Square damage thresholds: sustained ITT damage above 850 C, overspeed and turbine damage logic remain. This is not approval to operate at those ITT levels.
- V1 1/3 scaling of the custom torque indicator. Thus indicated torque is not direct ft-lb; a displayed 1,500 roughly represents 4,500 actual ft-lb before Black Square's other corrections.
- Existing X-90T aircraft identity, cockpit instruments, model and textures, fuel configuration, original Black Square package, and piston X-90 untouched.
How to install
- Exit MSFS 2020.
- Extract the complete installer ZIP.
- Double-click
INSTALL_X90T_V4.cmd. - Automatic folder detection searches your observed
E:\MSFS\Communitylocation and other paths; a folder chooser is a fallback. - A separate
X90T_V4_BACKUP_...folder appears alongside the X-90T, then it replaces just three files and rebuildslayout.json. - To undo, close MSFS and run
ROLLBACK_X90T_V4.cmd.
First V4 diagnostics, simulator only
On a clear day, with the same fuel load and configuration, start at ground idle with brakes set and use brief, incremental throttle applications at roughly 20%, 35%, 50%, and 65%; stop well before exceeding any indicated operating limits. Record prop RPM, actual ENG TORQUE (ft-lb if available via debug), Black Square indicated torque, ITT, Ng and FF, and whether brake-holding thrust grows with lever input. If RPM runs away or the engine loses power, report the first lever position at which it happens. Avoid takeoff until engine + governor response are predictable. After successful static tests, use moderate power on a long unobstructed runway and verify control margin before rotation.
No actual MSFS simulator flight test, governor verification, or Windows PowerShell execution occurred during packaging. The files were syntax/structure and ZIP-checked only.
Version control follows the airplane.
X-90T V4 is the latest packaged thrust-recovery baseline. Its flight behavior and 2,200 SHP target remain unverified. The X-90P has a user-reported 290 KIAS at 15,000 ft, not a certified performance figure.